Back to Blog
How-to Guides 2026-11-18 CameraMall 3 views

Lowepro ProTactic BP 350 AW II: Modular Backpack Setup Guide

Lowepro ProTactic BP 350 AW II: Modular Backpack Setup Guide

Set up the Lowepro ProTactic BP 350 AW II with a divider layout that fits your kit, four access panels, SlipLock add-ons, and a stable tripod carry.

Start with the load, not the dividers

The ProTactic BP 350 AW II is built around a specific working kit: one or two Pro DSLRs, including one with an attached 24-70mm f/2.8 lens, plus up to eight additional lenses or flash units, a tripod, and a laptop. Before you move a single divider, lay that kit out and decide which camera body stays ready to shoot. That body should sit where an access panel can reach it without unpacking the whole bag.

The bag gives you four access points: top, both sides, and back. Plan your divider layout around those openings rather than around a symmetrical grid. The goal is to reach the camera you use most from the top or a side, and to keep the rest of the kit secure behind dividers that match the actual width of your lenses.

What the bag is designed to carry

  • Lowepro ProTactic BP 350 AW II Backpack Black: Accommodates 1-2 Pro DSLRs, including one with an attached 24-70mm f/2.8 lens, plus 8 extra lenses or flash units, a tripod, and a 13" laptop. This is the capacity baseline for your divider plan. If your kit is smaller, you can use the spare space for access and padding rather than filling every slot.
    Lowepro ProTactic BP 350 AW II Backpack Black
    Lowepro ProTactic BP 350 AW II Backpack Black
  • Lowepro ProTactic BP 350 AW II Backpack Black: Four access points at the top, sides, and back help you organize your gear and quickly grab it to get a shot. Access drives the layout: place frequently used items near the top or side panels, and less-used gear toward the back.

Build a divider layout that matches your access points

Work from the camera body outward. Adjustable interior dividers let you create a snug, secure fit, so treat the first layout as a draft and refine it after a test carry.

  1. Place the primary body with its attached lens: Set the camera and 24-70mm f/2.8 in the section that lines up with the top or a side access panel. Leave enough clearance that the lens hood or strap does not catch when you pull the camera out.
  2. Group lenses by how often you change them: Put the two or three lenses you use most in the compartments nearest the side panels. Store backup lenses and flash units deeper in the bag, where the back panel or top opening can still reach them.
  3. Use dividers to separate hard edges: Adjustable dividers create snug, secure compartments. Give each lens its own slot rather than letting two share a wide bay, and use the dividers to keep camera bodies from knocking against lenses.
  4. Reserve the laptop pocket for the computer only: The CradleFit laptop pocket suspends and protects a 13" laptop. Keep it free of lenses or tools so the suspension works as intended.

Use the four access panels deliberately

The top opening is the fastest route to a camera you are already carrying on your shoulder. The side panels suit lens changes when the bag is on the ground or swung to one side. The back panel gives you full access to the main compartment when you need to reorganize or pack the bag for travel.

A practical configuration puts the primary camera at the top, the most-used lenses behind the side panels, and the less-frequent gear toward the back. If you shoot with two bodies, place the second body where a side panel can reach it, and keep the attached lens oriented so it clears the opening. The four access points are a layout tool: each compartment should have a clear path to at least one opening.

Add modular accessories with the SlipLock system

The SlipLock-compatible strap system lets you attach modular accessories to the outside of the bag. Five are included: a water bottle pouch, an accessory case, a tripod cup, and two cinch straps. Because they are all SlipLock-compatible, you can move them between attachment points as your kit changes.

Keep the outside configuration simple. A water bottle pouch on one side and the accessory case on the other preserves the side access panels for lens changes. Put the accessory case where it does not block a panel you use often, and check that each attachment is secure before you lift the bag by its harness.

Tripod carry hardware included with the bag

  • Lowepro ProTactic BP 350 AW II Backpack Black: Add a tripod or monopod to the outside of the bag using the included cinch straps and tripod cup. The tripod cup supports the feet while the cinch straps secure the legs. Use both together rather than relying on a strap alone.
  • Lowepro ProTactic BP 350 AW II Backpack Black: Five included modular accessories, including a water bottle pouch, accessory case, tripod cup, and two cinch straps, are all SlipLock-compatible. Knowing which pieces belong to the tripod carry keeps you from misplacing the cup or using the straps for something else.

Rig the tripod so it stays put

Attach the tripod before you load the bag onto your back, and recheck the straps after the first few minutes of carry.

  1. Seat the tripod feet in the cup: Place the tripod feet in the included tripod cup so the base cannot slide out sideways.
  2. Run the cinch straps around the legs: Use both included cinch straps to bind the tripod legs to the bag. Tighten them so the tripod cannot shift when you walk.
  3. Check the load before you lift: Lift the bag by the harness, not by the tripod, and confirm the tripod does not swing into a side access panel or the water bottle pouch.

Set up the harness for a loaded bag

The ActivZone System harness delivers targeted support at the shoulder blades, lumbar area, and waist. With a full kit, use the waist belt to take weight off your shoulders. The waist belt is easily removable for storage and travel, so you can strip it down when the bag is lightly loaded or when you need to pack it flat.

The built-in all-weather cover is your rain plan. Fit it before the weather turns rather than after the bag is wet, and check that it does not cover an access panel you need in a hurry. If you carry the bag through an airport, remember that the 13" laptop pocket and the bag's dimensions describe the bag's capacity, not airline acceptance; check your carrier's rules separately.

Comfort and weather features that affect your setup

  • Lowepro ProTactic BP 350 AW II Backpack Black: The ProTactic 350 AW II provides targeted comfort and support with its ActivZone System harness, which includes a waist belt that is easily removable for storage and travel. A heavy camera and lens load is easier to carry with the waist belt engaged. Removing it is a travel-packing decision, not a permanent change.
  • Lowepro ProTactic BP 350 AW II Backpack Black: The bag offers a built-in all-weather cover to safeguard your gear against the elements. The cover is part of the bag, so you do not need a separate rain shell, but you should confirm it does not block the access panel you rely on.

What to confirm before your first carry

The supplied product record confirms capacity, access points, SlipLock accessories, and harness features. It does not provide exterior dimensions, weight limits for the tripod carry, or airline acceptance. Treat those as checks you make against your own gear and carrier.

  • Test the primary camera exit: With the bag loaded, open the top and side panels and confirm the camera with the attached 24-70mm f/2.8 clears the opening without forcing the divider.
  • Confirm the laptop fits the CradleFit pocket: The pocket is designed for a 13" laptop. Check your computer's dimensions against the pocket before you rely on it.
  • Check the tripod carry with your tripod: The cup and cinch straps are included, but the record does not state a maximum tripod weight. Test your tripod on the bag before a long walk.
  • Verify airline rules separately: The bag's capacity does not guarantee overhead-bin or cabin acceptance. Check your airline's carry-on limits.

Related Articles

Customer Service
Home
Products
Cart
Profile